HORN DISTRIBUTING COMPANY   Wholesale Equipment Distributors for the Food Service Industry Home About Us  Manufacture & Products Refrigeration Division Request More Information Paragon Marketing Website

  GREEN MONSTER WIRE SHELVING SPECIFICATION SHEET

 1. GENERAL: Shelving shall be of the type produced by STORTEC SYSTEMS CO. It shall

    carry the approval of the National Sanitation Foundation (NSF)

2. MATERIAL: Shelves shall be bright basic carbon steel wire.  Posts shall be cold

    rolled carbon steel tubing, electric welded.

3. FINISH:  Dark green color. Surface preparation of steel to be zinc phosphate with epoxy

     powder coating electrostatically applied and thermostatically cured to a tough, hard

     finish. Ten year warranty against rust and corrosion.

4. SHELVES: Construction shall be of open wire design offering greater light penetration

     and visibility, lighter weight, air circulation and minimal dust and dirt accumulation.

5. FABRICATION;  Face ribs shall run front to back equally spaced on 13/16”  centers and to be

     of 9 gauge (0.148”)  wire. Each side  (four) of shelf shall consist of a corrugated, reinforcing

     truss of 6 gauge (0.192”)  wire. At the front and back of the shelf, this corrugated, reinforcing

     shall be welded to Ό” (0.250”)  rib wire running perpendicular and above the face ribs. A Ό”

     (0.250”) rib shall be welded to the bottom of the truss. At the ends of the shelf, the corrugated

     reinforcing truss shall be welded to parallel Ό” (0.250”) wire ribs. Depending upon the width

     and length of the shelf, it shall have three or five longitudinal ribs (0.192”wire)  welded to the

     face ribs. In addition, certain longer lengths shall have one or two corrugated reinforcing

     trusses (0.192”) welded to the underside. At each corner of the shelf there shall be a tapered,

     conical fitting made of 12 gauge (0.104”) cold rolled steel to the parallel rib supports. The fitting

     shall be designed to accommodate the vertical supports. The corrugated truss shall be in the

     shape of the letter “W”.

 6. POSTS: Shall be of 1” O.D. . round steel tubing, 16 gauge (0.062”)  thickness. They shall have

      rolled grooves spaced at 1” on centers along their length. The top of the post shall have a

      a finished plastic cap and the post bottom shall have a die cast insert threaded with an

      adjustable leveling foot. At each rolled groove there shall be consecutive numbers starting at

      the bottom of the post to facilitate installation of shelf clips.

 7. METHOD OF ASSEMBLY: Shall be of the Frustal-Conical design incorporating a two part

      tapered plastic clip. Engagement and locking shall be accomplished with a protruding

      bead on the inner circumference of the plastic clip which will match the groove in the post. Two

      plastic clips shall be attached to each corner post for each shelf. Both the clips and the

      corner fitting of the shelves shall have the identical taper to create a wedge effect, thereby

      locking the shelf securely in a rigid position. No screws or other fittings shall be required to

      effect this  assembly. Shelves shall be vertically adjustable on 1” increments.

  8. LOAD CAPACITY; 600-800 lbs. Per shelf evenly distributed, depending upon the size.                                                                                  

      Maximum load per assembled unit not to exceed 2000 lbs., without casters.

  9. PACKING; Shelves are packed 4 to carton except 54”, 60” and 72” lengths, which are packed

      2 to a carton. Posts are packed 4 to a carton.

     FREIGHT CLASSIFICATION; Shelving, steel, NOIBN, KDF, rating: class 70.

     STORTEC WIRE SHELVING MEETS U.S. GOVERNMENT SPECIFICATIONS

     MI L-S-40144C AND HAS BEEN CERTIFIED BY NATIONAL SANITATION FOUNDATION

     (NSF)